CANON IMAGERUNNER IR105 DRIVER

F 2 Loosen the screws [1], [2], [3], [4]; then, tighten the screw [5] to a torque of 1. If dirt cannot be removed, replace it. F F [4] [3] [5] [2] [1] A [2] [1]. Memo To form a loop, wind the charging wire once around a hex key, and twist the key 3 to 4 times. If an ADF is installed, remove it also. Now you can produce beautifully finished sets of documents in-house,including church bulletins that are stitched,folded,and trimmed; course syllabi or business reports with printed tabs and preprinted color covers and inserts; or sales reports,complete with Z-folded spreadsheets. Never bring the clip into contact with the sensor cover.

Uploader:	Zulkree
Date Added:	25 February 2006
File Size:	9.5 Mb
Operating Systems:	Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads:	73380
Price:	Free* [*Free Regsitration Required]

Calaméo - imageRUNNER iR Parts and Service Manual

Make the following selections in service mode: Memo Pre-Transfer Exposure Function: When removing the screw from the drum shaft gear, be sure to pay attention to the direction of gear rotation, i.

The IR can run complex black-and-white jobs at pages per minute.

Turn over the edge. Offering the most robust finishing capabilities. F [1] [3] [2] [2] [2] [1]. The harness clip [1] will separate into two during the work. Peel the backing sheet [2] and the protective sheet [3] from the attachment sheet [1], and attach the attachment sheet to the area [4] indicated in the figure.

F [2][1] [1] [1] [3] [1] [2] [1][2] [3].

If the reading is as indicated in Method 1 but is not in Method 2, suspect dirt on the sensor or a fault in the potential measurement unit. F [2][3] [1] [2] [1] [3] [3]. Paper is not at PS The cause is between scanner and CCD. Then, check the setting of the following in service mode: This Service Manual consists of the following chapters: Enlarged Image Composition Use it for automatic enlargement of a single original after dividing it into 2 or 4 parts for copying on paper of imagerinner specified size.

At this time, be sure to tighten the other terminal [3] of the grounding wire canno the right lower screw. Insert a flat-blade screwdriver into the top of the grip cover [1] 2 pc.

F [3] [1] [1] [5] [6] [7] [2] [5] [4] [4] [2] [1] [3]. F [2] [1] [1] [2][3][4].

imageRUNNER - Support - Download drivers, software and manuals - Canon UK

Waste toner can drop on the duplex unit when the process unit is removed. F [3] [2] [1] [1] [1] [1] [2]. As necessary, curtains must be provided.

The problem is not of the copier. Remove the separation releasing member [3]. Fa If for a V model, caonn the ferrite core [2].

Canon imageRUNNER 105

Whatever your printing needs may be,Canon has the specialty media available to meet them. Press the releasing button for the cassette, and slide it out to the front. If you must loosen it, be sure to adjust the position of the inlet guide afterward by referring to the index on the fixing assembly.

When mounting the fan, be sure that the direction of air is as indicated by the arrow. Route the harness through the imagerunner saddle [7].

Canon Photocopier ImageRUNNER 105

Feed direction c a Middle of paper b A3paper Dimension Measure with upper and lower rollers fully heated b V: If the ongoing job is cancelled, it kr105 execute dust detection at the end of operation. Remarks Clean with a blower brush; if dirt cannot be removed, use alcohol. The value is used to center the image position on the photosensitive drum.